Monday, January 5, 2015

how to build your own flexible LED Display XXL WS2811 real time Video Transmission

 
DIY How to build your own flexible LED Display Curtain XXL P16.6 realtime Video Transmission



Here we going to show you how to build a FLEXIBLE "ROLL AND FOLDABLE" LED Display WS2811. cheap easy and very useful Advertiser

 
TOOLS .:
  • Side cutter (sharp) 
  • Screwdrivers mix (cross, slot, big & small)  
  • Hot Iron (sharp tip)
  • Solder (thin)
  • Heat gun shrinkable tubing Puncher (to hole the Plane)
  • Detergent (cleaning)


First buy, order, collect all the needed Components for this Project, the most accessories are Optional means they’re modified for my project you can change the accessories like color of the PCBA waterproof or non Waterproof of the led strip IP65/IP68/and more, for this project we use an LED WS2811 realtime Video Controller LED Live transmission controller, The Surface you can change to different materials or colors. We are useing here an PVC Banner Flexible, robust, easy assembling, nice look ...  

We offer all the accessories and assembling parts for this project and many other LED projects (TOP PRICE TOP QUALITY incl. WARRANTY) so we will assist you for questions and Price inquires.
 
WARNING = BE AWARE OF CHEAP CRAP LED STRIPS (low price)
THERE ARE A LOT OF SCAMMERS ON THE MARKET HERE USE REFURBISH CHIPS SECOND HAND IC´S SECOND ASSEMBLY PARTS AND MORE:::
THIS WILL CAUSE A LOT OF FAILURES AND SHORTER LIFETIME




Assembly Parts.:
 
Surface (depending on your need flexible or fix)
 
LED Supply
Power Supply´s (5v depending on qty of LED Source)
Controller (Life transmittion controller)
Fast Connectors
 
Shrinking Tube ( to cover and protect your connections)
for free tell us if you want us to send you some Meters for free by

so lets start ....

step. 1

make your assembling parts & tools ready

Cut 2cm shrink tube pieces (for the soldering place calculate 2pcs each line)

Cut the connection bridge wires for each line

Cut shrink tube pieces cover it over your wire connection (use the heat gun to make them tight)

Cut your Power +red and ground wires you need (for the controller and for the Power supply)

remember for this project WS2811 we need each 8thmeter a new CURRENT supply

60leds mtr 120leds 2mtr 1Line, 480pcs LED´s you can calculate the watts depending on your LED supply

Connect your controller create the CBX file (support questions) and connect 3-4 lines first and test if "anything is working or shining you also can use the SD card of the realtime controller to see if it runs ..

 

Step. 2

Calculate the length of the LED strip you have to cut, depend on your final requested LED DISPLAY SIZE !

include the vertical distance of each string line into your calculation
Example. how do i calculate LED strips for LED Display, how to caculate LED strip lines for display  =
Strip Length , Strip width + your customized distance of each string. Means
if you want to build a 1000mm high display go on like that. 1000 / strip width + distance = how many strip lines you have to cut /5000mm is one roll then you know exactly how many rolls of WS2811 LED Strip you need for your project !
Now you’re able to cut your calculated numbers of LED strings on your requested length.
 
Step. 3
After you cut all the strings place it to a flat place which is convenient for you to work on it I prefer a huuge Table be careful to not harm your surface if you work on it like we did.. .
Now grab your prepared bridge connection cables and place them on your strings ,
use the hot iron to soldering one by one bridge wire to strip don’t mess up with the the input and output of LED strip take care on the arrows
 
we also offer fast connectors to connect the strip without soldering It’s not about cheap fast or slow, it´s about quality and the most robust method is the one i use as you can see. If you wanna use your display portable and carry it around the method should be fix, otherwise you have a lot of maintainance..
Soldering the strips in a series circuit means the start of the first strip is every time INPUT, you can start everywhere you want with the INPUT but later in the software you have to change or setup your PORT. !
Don’t forget to cover a short 20mm pcs shrink tube over the strip before you soldering the wire otherwise you have to remove the solder again and cover the shrink tube it’s easier to cover them before. pull the shrinkpiece far enough inside that the heat will not shrink him to early .
 
 
Step. 4
After you solder (connect) each strip with the other and make a short test give the strips power and try a test with the LED file on the SD card. or connect the Laptop with an LAN cable to the controller and open the software. Cover the shrinking tube over the solder place and use the Heat gun to make it tightly and secured.
After use the heat gun you should bring the strip lines and the connecting wire in ENDPOSITION hold it by hand till the shrink tube will become cold and tight, you can form it as you like, after some seconds it’s tight and will not move again stay in position. !
 
 
Step. 5
Now you move the strip construct by side, add your Plane surface to the Table, and clean it careful.
Place your LED strip construct to the surface.
BRING IT IN POSITION use the meter stick to fix each distance that the strip construct later Placed well in exactly the middle of your surface.
Now you can fix the first LED strip line peel the paper from the backside of the strip (glue), hold one side to the up and start from the other side to fix it.
Use your meter stick or caliper to recheck if your strip is straight in position..!
IMPORTANT.: If you start to place the first line awry the deviation in the end will be much bigger and later show each awry placements and BIG deviation.
 
 
Step. 6  
Now you fixed the whole LED construct to the Surface it’s time to check it again, connect it to power again, if workable we go on like that...
Use the Puncher to place a little hole EXACLY under the start of the LED strip Input, put the input wire through the hole. Place the SD controller on the backside of the surface by adhesive tape double sided, connect the wires from the input with the SD controller, connect your power supply and you’re done.
 
 
Step. 7
Join, sell, rent, advertise and Publish your stuff on your new WS2811 flexible LED Display curtain with realtime Video controller …. There are many ways to get back your invested Money Time and Power of this Project.
 
If I forget some important please reply us or recheck in the Video also for information about the products the strip the power supply finished products and so on we’d like to support you fast as possible
Thanks for watching....



16 comments:

  1. Hi
    Is it possible to send me all the links to products you used because I can't find them....
    Thanks so much !
    (you can conract me at thezeb42@gmail.com thx)

    ReplyDelete
  2. Would it be possible to build modular panels for a video wall or dance floor using the above. If so, what would you recommend for a 3m x 3m floor; what video controller or controllers would you recomment using. And what power supply or how many power supplies would be needed (each panel 500x500mm with WS2811 - P16.6). Thanks.

    ReplyDelete
  3. hi yeah thats possible, but i recommend you our new panel, its actually more easy to install, i will add the picture to this blog, for power details and all please contact us by email .

    ReplyDelete
  4. I need a simple explaintion , i found an explantion that its an imaginary boder between the east and the west but east and west of what country ?
    Videowall

    ReplyDelete
  5. Hello I'd like to receive a quotation for a project like yours (2000 x 1500 mm). Do you send the wiring diagram too? Software used is lededit? ftsouza@gmail.com

    Thanks,

    ReplyDelete
  6. Good day Sir,Ma'am!

    Happy New Year!

    I really love this! We have a research project which is a LED Bulletin Board. I am not that technologically advanced to figure out what materials you have used. Can you please e-mail me a list of every material you used including the name or model number so that we can easily find it on each link? This is for educational purposes only.

    Thank you so much for the help you and information that you could give us. It's really a big help for student like us.

    ReplyDelete
  7. Good day Sir,Ma'am!

    Happy New Year!

    I really love this! We have a research project which is a LED Bulletin Board. I am not that technologically advanced to figure out what materials you have used. Can you please e-mail me a list of every material you used including the name or model number so that we can easily find it on each link? This is for educational purposes only.

    Thank you so much for the help you and information that you could give us. It's really a big help for student like us.

    ReplyDelete
  8. Hello, can you send me the list of materials for this project 2000x1500 and the cost of total. I,m from Spain. I, don,t see the PVC surface in your web and I liked this material for my project.
    My email is: elorquestero@yahoo.es

    Thanks



    ReplyDelete
    Replies
    1. shop.elektric-junkys.com check it out or send us an email support@elektric-junkys.com

      Delete
  9. I want to know how far its visible because I am planning to set it up to a hill with solar power..

    ReplyDelete
  10. GUYS BUY ALL NEEDED PARTS FOR THE PROJECT HERE ... shop.elektric-junkys.com

    ReplyDelete
  11. Hi, Very cool article. that's exactly what I'm looking. i'm panino a video wall 3,50m x2,50 m in distance! about 1,5m. could you please send me an offer for the needed parts? thanke in advance.

    ReplyDelete
  12. This comment has been removed by the author.

    ReplyDelete
  13. Is it possible to get a parts list and instructions for the unit built in this video. If you sell these a link to them would be nice.
    Thanks
    Dog

    ReplyDelete